跳至主要内容

Attention Here! Professional Guide for iPhone 7 / 7Plus Unlock


Here we discuss about new unlock tool for iPhone 7 7plus -  IP-BOX V3, a professional iPhone screen passcode cracking Tool for skilled cell phone technician. It is pretty useful and we will list detailed operating introduction for educational propuse. Hope it will help you!


Step 1

Firstly, access the vulnerability interface of limitless input on iphone, entering password continually till it is deactivated for 15 minutes,  you can connect PP assistant( or similar iphone restore tool) to root the system with data protection ( the system version should be rooted higher than the present one so that the vulnerability will occur) If  no vulnerability for system 10.32, please root system 10.32  to system 10.33 or Test Vesion 11. Make sure you root system with data protection (Recovery/Backup the data), or your device will stop working. and you can enable your device by the data protection.

Step 2

Introduction for ports: 7 ports on the equipment, which includes USB 3.0 data cables for 3 ports, side light sensor port, iPhone and Android port for charging, and the side Android prot is for connecting computer to set password or upgrading.

Step 3

After entering the vulnerability interface of limitless input, connect device with mobile phone, then fasten the light sensor at the top of screen, the first sensor is cimpatible with first USB port, and so on, you should operate with proper order. Press the first button after equipment 1 shows “connected”, operation is no need after the equipment can input automatically. The equipment will pause automatically if the correct password is matched,  it will beep and remind you, the correct password will displayed on screen,  enter the password into system by yourself.

Step 4

Software Setting: The default setting arranges frequently-used at the beginning, it will scan other password automatically without repetition. Default setting is 6-digit password since it is popular, if you need setting 4-digit one, please correct by downloading computer control software.There are options for them. If you need setting your desired password, please use software to generate password.

Step 5 

Answer for common problems: if you need setting password without connecting computer, long press the corresponding button for 3 seconds. If fail, try again by outage. If mobile phone is power off automatically during the proccess, it means the electric current is not enough, cannot offer charging for phone at the same time. Solution: 1. change another high-current adapter 2. plug another cable to offer double-charging, if fail , plus another one to offer 3 charging.

(At present only support iPhone 7 and 7 plus) iPhone 6 and 6s also can be unlocked in the future, the software can be updated, you just need to correct equipment with computer to open software. If the speed of other solution can be improved, we will upgrade server immediately for your convenient operation.





Client software download:
https://drive.google.com/file/d/0BzMEvK0bAD0edXhjSVBKcnlKVFE/view?usp=sharing
How to Access iSO bug:

https://youtu.be/-Wq_C1098V4
how to connect the cables
https://www.youtube.com/watch?v=03HhsMGJCs0
pre-defined password and user demo video:
https://www.youtube.com/watch?v=9vroIcRaa3I


Read more at www.vipfixphone.com

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...
1 条评论
阅读全文