跳至主要内容

Solution: iPhone 6 Screen cannot Work

iPhone 6 touch is properly ineffective, when touch is not working, screen can display normally; the touch gets complete failure when there are some not obvious lines on screen. The device got water damage and screen was replaced, It's still not repaired well though repaired by another repairman.

Tear down the iPhone 6 to check out, we find both black and white touch were replaced, some capacitance under audio IC get slight corrosion.  First measure the positive and negative 5.7V power supply to the ground value, +5.7V positive measurement is 400+, - 5.7V negative measurement is 600+, both are normal as shown in picture 3-7-1.


We did not find obvious problems after ground value measurement, in accordance with the exclusion method, we firstly replace black touch, test failure is same, then replace the white touch, test failure still exist. It means there is no problem on IC, and also no obvious problem we can find from the power value. Thus, the fault point should be on the display screen IC U1501 because it didn't apply the power supply, as shown in picture 3-7-2. Immediately remove the CPU shield to check U1501, we found the traces of welding which indicates last repairman is professional.

Remove the U1501 and check the solde pad, we can't find obvious corrosion and disconnection, as shown in picture 3-7-3.

Measure the U1501 pad to ground value by multemeter,  -5.7V power supply output pin is normal 690+, +5.7V power supply output has no ground value, as shown in picture 3-7-4 and 3-7-5.



According to the backside +5.7V touch power supply has 400+ to the ground value as we tested, we can judge that the board is disconnected. As shown in picture 3-7-6.


Handle the pad with jumper wire (it's power supply here, output is recommended with amplifiers cable instead of headphones cable), and the pins(as shown in picture 3-7-7) on the IC are also need to be handled.


Sodering IC, measure booster ground value and +5.7V ground value with multemeter. As shown in picture 3-7-8, 3-7-9 and 3-7-10.




Booster and the touch +5.7V power supply to the ground value are normal, install screen to test, the touch can work normally as shown in picture 3-7-11.

Soldering jumper wire, cover it with brown adhesive tape, welding the shield cover, the iPhone 6 successfully repaired as shown in picture 3-7-12.



More cell phone repair skills check at www.vipfixphone.com














评论

发表评论

此博客中的热门博文

Solution: Why iPhone X Voltage Keeps Jumping

After getting the iPhone X motherboard to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU  power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
发表评论
阅读全文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文