How to Fix iPhone 7 Charging Failure

We got an iPhone 7 from customer, according to his decription, the device fault is the single side displays charging, the other side did not display and also not charge. Get the device to test all the functions first, there are no other problems. It is found by multimeter that the single side display can't get power in at all, and the other side does not display or enter the electricity.

Firstly, take an iPhone 7 charging port to replace, we need to exclude the possibility of faulty external spart parts.

After replacing the charging port, the same problem still exists, the single side has diplay but no electricity. As shown in pictur 10-5-1.

Next, disassemble the iPhone to replace chip, this problem is generally caused by USB management chip. As shown in picture 10-5-2.

Remove the screen we find the fingerprint inside, it is same after the replacement of charging port parts. Disassemble the iPhone 7 motherboard to find the USB management chip motherboard, we do not know which chip it is, so now take iPhone 7 schematic diagram directly, we search the 1610 and find the part soon, as shown in picture 10-5-3.

Read the point bitmap and quickly located to U4001, as shown in picture 10-5-4.

The object is shown in 10-5-5. As the shield covers the chip, apply the nail clipper directly.

Now dismantle directly with high temperature and fast speed, it should be done in 10 seconds.

Open the electric multimeter,we find the current is 700mA, then we change the side, it can also be normally charged. Now there is 79% battery power, wait a minute to see if there is power get in then we will install it. As shown in picture 10-5-6.

After a while, there are 83% of the iPhone 7 battery power, it should be no problem, install the iPhone 7 device, repair is finished here!

More cell phone repair information, please view on www.vipfixphone.com

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC output is normal. Testing by DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...

阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...

阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2 sets of circuit 1) PP_LCM_BL_ANODE, PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE, PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...

阅读全文

Professional Cell Phone Repair Guide

搜索此博客