跳至主要内容

Solution: iPhone 6 Plus Fingerprint & Camera Not Working

We are going to repair an iPhone 6 Plus device with fingerprint, front and rear camera fault, the customer described the iPhone black touch IC was repaired before, it is possible to put the back of the component virtual weld. Anyway, we need to fix it step by step.


First of all, measure the diode data of rear camera adapter with Fluke 15B+ Digital Multimeter, no exceptions found. Then measure the rear camera power supply.


Measure the main camera 1.8V and 1.2V power supply, when we measured the 2.85V power supply, we found that it had no power. Check the iPhone 6 Plus schematic diagram on WUXINJIDongle to trace the 2.85V source.


We found that the 2.85V was converted from the main power supply through U2301. During the repair process, short connection A1 and A2 pin can quickly determine if 2.85V power is causing the iPhone camera not working. After short connect A1 and A2 pin, get into IOS to test the iPhone rear camera, it can be turned on now, but short connect 2.85V conversion tube can only test whether it is caused by 2.85V. We can't stop the repairs, because the voltage of PP_VCC_MAIN is 4V, but the power supply of this circuit is 2.85V.


Direct short connection, take pictures in the darkness, sometimes there are white stripes, you not only can replace the conversion tube here, but also can weld jump wire from the iPhone Nand flash 3V. Generally we weld the jump wire from iPhone Nandflash 3V power supply.


After finished the welded jump wire, we start to repair fingerprint. First measure the diode data of fingerprint socket. When measured the 12th pin AP_TO_MESA_SPI_MOSI_CONN, its resistance is infinitely large. Trace AP_TO_MESA_SPI_MOSI_CONN signal, we found that it was renamed directly by AP_TOMESA_SPI_MOSI through inductance fl2132. Since there are components in the middle, then we just check FL2132 under the 7-45X 180X Stereo Zoom Microscope


Gently wave the components with Precision Titanium Alloy Tweezers, we found it had fallen off. According to iPhone circuit diagram, we know that this inductance is an insurance inductor; the insurance inductor can short-circuit the two pins directly together. When finished, assemble iPhone and test, fingerprints are fine now, the repairs end!



More professional cell phone repair tutorials read at www.vipfixphone.com


标签：

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...
1 条评论
阅读全文