跳至主要内容

Fixed: iPhone 6 6P Audio Parts Repair


The audio parts of iPhone are mainly including audio decode, u0900, ringtone (horn), and amplifier. Check the iPhone 6 diagram on wuxinji dongle. We can see that the iPhone audio integrated circuit has 4 circuits, one is vcc_main, 3.7V, the other three is 1.8V. After checking the power part , then we check the iPhone audio channel part, we can see the direction of the audio signal on iPhone schematic diagram.

At first, check the normal call mode. Two microphone signals LOWERMIC1_TO_CODEC_N_CONN, LOWERMIC1_TO_CODEC_P_CONN through iPhone tail plug flex cable and 17/18 pin of tail plug interface J1817, after the inductance FL1881, FL1882, finally through the capacitor C0922, C0923 send to audio IC-- U0900.  The 1.8V power supply signal PP_CODEC_TO_MIC1_BIAS that was sent from audio IC U0900, through FL1 and 21 Pin of interface J1817, after through tail plug circuit, the final supply to the microphone. This is the process of microphone signal.

The iPhone 6 earpiece signal from the audio IC U0900 K7,L7 pin through inductance FL1151, FL1152 send to 1/3 pin of interface J111, and then through earpiece (sensor and iPhone front camera) circuit line to earpiece.

Now move on the iPhone 6 audio channel in speaker mode. the transmitter signal FRONTMIC3_TO_CODEC_N_CONNFRONIMIC3_TOCODEC_P_CONN through interface J111 and pass inductance FL1103, FL1101, finally send to iPhone audio IC U0900.The speaker signal from audio amplifier U1601, and then through tail plug interface J1817, finally send to speaker.

What we need to notice is that there is a another mode that the iPhone microphone is on the boot circuit when it in the state of the video. The recording signal through the boot line interface, and then after the inductance FL0801 FL0802 sent to U0900, which means that if an iPhone has other voice but the video was silent, then you can fix it by replacing boot line or boot line interface.

There are 3 status as following:


1. If the sound of a certain circuit is abnormal, such as there was a handset, but no sound, or other handset no sound issues, we need to check whether the inductors or resistors that pass through the channel are corrosive, check earpiece circuit line or microphone circuit line. After excluding these, if the failure still exists, then you need re-install or replace U0900.
2. If the iPhone is no sound at all, firstly check the several power supply circuit line on U0900, if the power supply is normal, then re-install it or replace the audio IC U0900 by using hot air gun.

3. If there's a voice when it on the phone calls, but no ringtone and no speaker, mostly it is the iPhone amplifier IC problem. When face this problem, first exclude the tail plug line issue, measure the battery power supply of C1695 to check if it is normal, check inductance L1604 for damage, check C1630 1.8V for normal, after excluding above issues, replace U1601.

4. If no sound on the phone calls but the recording is normal, not only is the damaged or virtual welding audio IC can cause this problem, but the virtual soldering of the iPhonebaseband CPU can also cause this problem.

If you want to get more iPhone repair tutorials, www.vipfixphone.com will be the best website for your reference!

评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...

Solution: iPhone X Won't Turn On

According to the customer's description, the iPhone X would not turn on after it drop accidentally. Then the cell phone reports error 56 when restore it. How did this happen? Let's test and repair step by step. Since iPhone X motherboard 2 layers are connected through the middle column, the solder points are very easy to get dropped. so we guess that the solder points from NFC chip to the CPU part have fell off. Disassemble the iPhone X by iPhone opening tools , remove the upper board off the main board, when separate the main board we see there is a row of points have fell off. Check the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Then the tin of the middle column is repaired by iPhone X BGA reballing ste...

Guide: iPhone 7 Plus Camera Fault Repair

iPhone camera failure is common for most of cell phone repair technicians, today, we're going to fix iPhone 7 Plus camera. According to the holder's description, the front small camera is normal while the rear camera fails to take photos, when turn on it, the iPhone 7 shows black screen. Let's start from easy repair operation: directly replace the iPhone camera to have a test.  Note: Pay attention that two camera are connected together. When disassemble the iPhone 7P rear camera , you need to pry up from the left side.  The fault is same as before after replacing a new rear camera. We tested before, the iPhone 7P double camera is rely on the bigger camera to get image, as shown in 15-5-1, the corresponding part on iPhone 7P motherboard is J4501 pin, the resistance value is normal after testing with Fluke 15B+ digital multimeter , it reminds of us that iPhone6 Plus also encountered this phenomenon, the power supply part has some problem. By checking on  WUXINJ...