跳至主要内容

Guide: iPhone 6s Camera Part Repair


Sometimes front or rea camera can't be used normally, it is a common problem of the mobile phone. If the same problem is found on your iPhone 6S, how should you diagnose and repair it?



1. Rear Camera Repair

First, we take out WUXINJI schematic diagram and read the power supply circuit diagram of iPhone 6S. There are three circuit of power supply in total:

One of the circuit is 1.2V PP1V2_CAMERA from the power supply IC, the 1.2V power supply was sent to rear camera interface J3200 through inductor FL3201, if the voltage is not sent to the iPhone 6s rear camera interface, it is generally caused by FL3201 corrosion, use jumper wire to do short connection will solve the problem.

The second circuit is 1.8V from the IC power supply, 1.8V power supply was sent to FL3220 rear camera interface through inductor FL3220, and inductor 3220 is easy to get corrosion damage so that 1.8V is not able to be sent to rear camera interface, use jumper wire to do short connection will solve the problem.

The last circuit power 2.85V is supplied by U3200, the U3200 output voltage 2.85V was sent to rear camera interface through inductor FL3202, the rear camera fault is mostly caused by U3200 damage so that 2.85V is not able to be supplied to rear camera, the 2.85V voltage is not able to be tested by Fluke 15B+ Digital Multimeter until there is resistance C3200 when taking photos. It's not easy to measure because of narrow place, so we can connect an enameled wire on capacitor C3200 for convenient measurement. Turn on the camera and test it immediately. If it is a good handset, it can measure 2. 85V voltage, if the 2.85V voltage is not measured when the camera is turned on, it indicates that U3200 is damaged. This situation can be also solved by phone repair jumper wire short connection.


2. Front Camera Repair

If the front camera can not work normally, check the FL3100 FL3102 FL3104 short connection. Re-stall or replace the iPhone 6s power IC 

In addition, the flash IC damage will also cause failure to take photos or videos. Replace the iPhone 6s flash IC can fix the problem.

More cell phone repair tutorial and guide please read on www.vipfixphone.com

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...
1 条评论
阅读全文