跳至主要内容

iPhone 6S Plus Charging Failure


Charging failure is a common problem in cell phone repairs, here we are going to talk about how to test and repair iPhone 6S Plus charging failure. iPhone 6S Plus charging failure, including the iPhone battery power percentage is getting less during the charging, power down status can be charged successfully but cannot charge after boot and unable to recognize USB, etc.


Check iPhone schematic diagram on WUXINJI Dongle, we found that the PP5V0_USB(5.0V) that was sent from the iPhone Tail Plug circuit, and then continue sent to the charging IC via the trailing plug interface, and then go through the charging protect tube, finally send it to iPhone USB control IC.

After disassemble the iPhone by phone opening tools, remove the iPhone motherboard, use Fluke 15B+Digital Multimeter to measure the 5.0V voltage (PP5V0_USB) next to the charging IC, and then measure the 5.0V voltage (PP5V0_USB) next to the USB control IC to check is it working properly.

If both these 5.0V is working properly, then you just need replace the iPhone charging IC and USB control IC.

If 5.0V(PP5V0_USB) next to charging IC exist, but 5.0V(PP5V0_USB) next to USB control IC doesn't exist, the iPhone power down status can be charged successfully but cannot charge after boot, or can't recognize USB. In order to fix this trouble, we can use hot air gun to short connect charge protection tube.

Moreover, damaged charging capacitor L2300 also will cause iPhone power percentage won't increase during the charging.

If you want to get any cell phone repair skills or tutorials, please click www.vipfixphone.com

评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...

Solution: iPhone X Won't Turn On

According to the customer's description, the iPhone X would not turn on after it drop accidentally. Then the cell phone reports error 56 when restore it. How did this happen? Let's test and repair step by step. Since iPhone X motherboard 2 layers are connected through the middle column, the solder points are very easy to get dropped. so we guess that the solder points from NFC chip to the CPU part have fell off. Disassemble the iPhone X by iPhone opening tools , remove the upper board off the main board, when separate the main board we see there is a row of points have fell off. Check the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Then the tin of the middle column is repaired by iPhone X BGA reballing ste...

Guide: iPhone 7 Plus Camera Fault Repair

iPhone camera failure is common for most of cell phone repair technicians, today, we're going to fix iPhone 7 Plus camera. According to the holder's description, the front small camera is normal while the rear camera fails to take photos, when turn on it, the iPhone 7 shows black screen. Let's start from easy repair operation: directly replace the iPhone camera to have a test.  Note: Pay attention that two camera are connected together. When disassemble the iPhone 7P rear camera , you need to pry up from the left side.  The fault is same as before after replacing a new rear camera. We tested before, the iPhone 7P double camera is rely on the bigger camera to get image, as shown in 15-5-1, the corresponding part on iPhone 7P motherboard is J4501 pin, the resistance value is normal after testing with Fluke 15B+ digital multimeter , it reminds of us that iPhone6 Plus also encountered this phenomenon, the power supply part has some problem. By checking on  WUXINJ...