跳至主要内容

Repair Guide: iPhone 7 7P Fingerprint & Home Button Repair


If the fingerprint and home button function on iPhone 7 / 7p get failure and you don't know how to fix it, now this article will be your guide for the detailed repair process! Hope it will help!
 

Before repairing, open the WUXINJIDongle to check iPhone 7/7P schematic diagram.


1. iPhone 7/7P home button repair guide

The home button power supply schematic diagram is as follows:

The power supply pipe U3801 output PP2V75_MAMBA(275V) to J3801, iPhone power IC output PP1V8_TOUCH(1.8V) , through resistance R3805, final to J38011.

If these two circuit power supply is abnormal, it will cause iPhone home button failure. For repairing this problem, check short connection R3805, and then you can replace the U3801 or disassemble the U3801, and then use PPD 861D Plus hot air rework station to weld the jump wire from C3813 to C3823.

Tips:

PP3V0_MESA(3.0V), PP1V8_MESA(1.8V), PP2V75_MAMBA(2.75V) and PP1V8_TOUCH(1.8V), this four circuits voltage can be tested by pressing the iPhone power button.
2. iPhone 7/7P fingerprint repair guide

The fingerprint power supply schematic diagram is as follows:

The iPhone power IC output PP3V0_MESA(3.0V) PP1V8_MESA(1.8V) respectively through inductance FL3803 and FL3801, next send it to interface J3801; the iPhone power supply IC-- U3702 output PP16V0_MESA(16.0V), after inductance FL3802 delivers to the interface U3801.

If these three circuits power supply is abnormal, it will cause iPhone fingerprint failure. In order to fix it, you can check the short connection FL3803, FL3801 and FL3802, use Precision Titanium Alloy Tweezers to replace the U3702.

More iPhone repair skills or related tool you have need, please check on www.vipfixphone.com


评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...
1 条评论
阅读全文