跳至主要内容

The Best Solution for iPhone 6 Charging Failure

Have you ever met the same situation on your iPhone 6? iPhone 6 charging failure is very common for cell phone repair professionals. However, there are many different reasons may cause this failure. In this article, we are going to fix the fault step by step, let's have a look how to solve it:
1. After taking off iPhone 6 screen, directly test the battery seat voltage B+ with Fluke 15B+ Digital Multimeter, it is 0.46 V, there is no voltage can directly exclude the battery problem.

2. Test battery seat resistance B+385 (abnormal resistance will cause white apple restart symptom) normal, disassemble the single board test the 5V sent by USB. There is a test point below the battery interface. If there is 5V, it means there is no problem with the tail plug flex cable(if not, then replace a new tail plug flex cable to test again).
Now we are continue to test the IC with failure

3. Use multimeter to measure whether the capacitance C1704, C1408 has 5V voltage, if neither of them has 5V voltage, you can short connect Q1701' s pin 1 and pin 3. If either of the two capacitance has 5V voltage, then jumper wire can help to solve. At the same time, Q1701 may cause the phenomenon: turn off the iPhone 6 can be charged while boot can not be charged. the same method short connection can be applied for solving this problem.
4. If both 5V power supply are normal, then test the 4.2V on the battery seat and test the C1417 and C1412. If either of them has no 4.2V, you can short connect Q1403; If both of them have no normal voltage, then you can replace the U2 (U1700) or the U1401 charge tube. U1401 charging tube damage usually has charging icon, and the more electric charge is, the less charge will increase, it won't increase anymore when approaching the certain electric charge.

5. U2 is easy to get damaged in iPhone repair(single board boot 250mA, with DC power supply, it will auto jump about 200mA, battery power display is inaccurate, battery power consumption fast, unable to identify USB, non computer and so on).
8. The NAND is on the top of U2, and there is baseband power below U2. There is a baseband CPU on the back of it. Before disassembly, you can use heat resistant tape to protect the ICs from high temperature and cause other problems. Charging fault detection method for iPhone is basically universal (U2 chip A3B model is common used for iPhone 7).

If you want to get more iPhone repair tutorials and related repair tools, please visit www.vipfixphone.com
标签：

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...
1 条评论
阅读全文