How to Fix the iPhone 5S Charge Failure

The iPhone 5S has a charging fault, such as the iPhone that can be charged when it is turning on, but it can't be charged when it turns off, or it doesn't support the accessory, or it can't be recharged at all. How to repair the charge failure on iPhone 5S? Let's have a look in the article!

Check iPhone 5S circuit diagram on WUXINJI Dongle, we know that after plug the iPhone lightning cable, the charge voltage PP5V0_USB_PROT first passes through Q2, then to U2, and then to the iPhone power supply IC--U7, we can measure the voltage of 5V to U2 by Fluke 15B+ Digital Multimeter at point C272, and the 5V voltage can be measured at point C304.

If 5V cannot be measured at C304 and C32 points, this means that Q2 is damaged. In this case, we need a short connection to Q2, as shown in picture 1-1 below.

If one has 5V and the other not, which means there is a disconnection. In this case, we will use QUICK 861DW hot air rework station to solder a jump wire from C304 to C272.

Note:

1. If the C304 or C272 doesn't have the voltage, it will cause iPhone can be charge only when it is turned off or is the hint that the accessory is not supported

2. The iPhone 5S USB control IC--U2 is easy to damage, and then cause iPhone cannot be charged, cannot connect to computer and won't boot issues, so we need to replace the iPhoneUSB charge IC--U2.

3. The damaged iPhone battery and iPhone tail plug flex cable also can cause iPhone charge failures, such as won't charge, "this accessory is not supported", or the percentage of charge icon is getting less when the iPhone in charging, so we need to replace the new iPhone batter or iPhone tail plug flex cable.

If you you think the article is useful and need more cell phone repair information, please check on www.vipfixphone.com

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC output is normal. Testing by DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...

阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...

阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2 sets of circuit 1) PP_LCM_BL_ANODE, PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE, PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...

阅读全文

Professional Cell Phone Repair Guide

搜索此博客