跳至主要内容

Repair: iPhone 5S Blue Screen Reboot Repair

Blue screen reboot is a common problem for iPhone 5s device, for different users, there are also a lot of different reasons caused. In this article, we'll list 7 possible faults would happen on iPhone 5s device, hope it will help!


1. The screws in the red circles below are different from elsewhere. The screw holes below are empty, and the two screws below are motherboard. When you twist the screws, you will damage the iPhone motherboard immediately, it will cause White Apple logo stuck on screen and blue screen reboot, error 14 or 9. You need to especially pay attention to the two screws. It looks very strong and easy to misunderstand with big screws. The 5S motherboard can be easily damaged when many beginners  disassemble and assemble it.


Remove the screwdriver with a HAKKO FX-951 soldering iron! Gently scrape with the blade, you can see the broken wire! As shown in picture 2, you can connect it with a thin speaker wire.

2. U6 pseudo welding or damage would result in a blue screen reboot, error 14.

3. USB control IC--U2 damage can also cause this blue screen reboot problem.

4. power IC pseudo welding will also cause the blue screen reboot problem.

5. iPhone compass IC must not be ignored! This magic small IC will not only cause blue screen reboot, it will also cause red screen reboot, many lines of English displayed on screen, white apple logo stuck on screen and many other strange phenomenon, error and so on. When you meet the above phenomenons on your iPhone 5s, the compass IC must be replaced instead of removing it.

6. In addition, the induction cable will also cause the phenomenon of not turning on many lines of English or blue screen reboot.

7. Another kind of blue screen reboot is due to the battery or the battery interface of the middle battery detection open circuit or short circuit, in this kind if case, you can enter into the system, but it will blue screen reboot again after 1-2 minutes. Measure battery and check the resistance of pin with Fluke 15B+Digital Multimeter, after eliminating the short circuit or open circuit problem, you can replace battery to have a try.

If you have any other problems for iPhone repair, please contact and result on www.vipfixphone.com

评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...

Solution: Why iPhone X Voltage Keeps Jumping

After getting the iPhone X motherboard to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU  power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...