跳至主要内容

Fixed: iPhone 6 No Display


A customer sent us a iPhone 6 to fix it. The fault described is that iPhone 6 will not turn on. But after testing, the real problem with this iPhone 6 is not shown after startup. How to fix it?

First of all, use phone opening tools to disassemble it and remove the iPhone 6 logic board.

The iPhone logic board looks good, no trace of water-damaged or traces of external pressure are found.

Connect iPhone logic board to DPS DC power supply to test it, the boot current tested is normal, but the iPhone LCD screen still no display, always keep black.

Measure the resistance value of the J2019 by digital multimeter, the resistance value is normal. Now, measure the voltage, there are no positive and negative 5.7V, and we suspect that the U1501 is damaged.

Remove the U1501 by Titanium Alloy Tweezers, and then install the new one to the iPhone logic board. After replacement, measure it again, but the 5.7V still can't be measured, we think the boost has some problem.

Check iPhone schematic diagram in the WUXINJI Dongle, from the iPhone schematic diagram, we need to replace the C1529 and C1502. After replacement, measure the iPhone again, now the data is normal.


Reinstall the iPhone and turn on to test again, the iPhone LCD screen displays normally now.

If you want to get more professional cell phone repair guide, please check on www.vipfixphone.com

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Solution: iPhone X Won't Turn On

According to the customer's description, the iPhone X would not turn on after it drop accidentally. Then the cell phone reports error 56 when restore it. How did this happen? Let's test and repair step by step. Since iPhone X motherboard 2 layers are connected through the middle column, the solder points are very easy to get dropped. so we guess that the solder points from NFC chip to the CPU part have fell off. Disassemble the iPhone X by iPhone opening tools , remove the upper board off the main board, when separate the main board we see there is a row of points have fell off. Check the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Then the tin of the middle column is repaired by iPhone X BGA reballing ste...
发表评论
阅读全文

Guide: iPhone 7 Plus Camera Fault Repair

iPhone camera failure is common for most of cell phone repair technicians, today, we're going to fix iPhone 7 Plus camera. According to the holder's description, the front small camera is normal while the rear camera fails to take photos, when turn on it, the iPhone 7 shows black screen. Let's start from easy repair operation: directly replace the iPhone camera to have a test.  Note: Pay attention that two camera are connected together. When disassemble the iPhone 7P rear camera , you need to pry up from the left side.  The fault is same as before after replacing a new rear camera. We tested before, the iPhone 7P double camera is rely on the bigger camera to get image, as shown in 15-5-1, the corresponding part on iPhone 7P motherboard is J4501 pin, the resistance value is normal after testing with Fluke 15B+ digital multimeter , it reminds of us that iPhone6 Plus also encountered this phenomenon, the power supply part has some problem. By checking on  WUXINJ...
3 条评论
阅读全文