跳至主要内容

Fixed: iPhone 6S Error 4013


The iPhone 6S reports error 4013, after checking it, we found there are watermarks on the board and it is corroded near the base band. How shall we repair the problem?

Test the iPhone motherboard with DPS DC power supply, the current stuck on about 80mA, judged as a data-cable mode. Install the iPhone 6S and use iTunes to flash it, the failure still there, the iTunes still reports error 4013.

At this time,we need to check the iPhone carefully to find out the fault part. First we check iPhone baseband circuit, if the iPhone baseband power is short circuit, if the resistance is normal and whether the 19.2 clock is normal. Replace the better iPhone baseband CPU, if the iTunes process bar can be moved, then iPhone baseband CPU may be damaged.


After disassemble it, we found the corrosion phenomenon around the iPhone baseband power is very serious, first suspected baseband power supply. Use QUICK 861DW hot air rework station to remove the iPhone baseband power supply, and then install the new one, but the problem still there after replacement. Next step, we need to open the iPhone baseband protective cover to check whether the iPhone baseband is damaged.

Open the baseband protective cover, and check iPhone logic board under the Stereo ZoomMicroscope, there were no traces of water near the baseband, and the preservation was intact. Does it mean the iPhone baseband CPU is damaged internally?


After observe it carefully, we found that the screw hole BS0502 has been penetrated, and several circuits on the bottom of the layer board are disconnected.


Reconnect them, install iPhone 6S and flicker again, it works. Enter iOS and test all functions on iPhone, all work is normal, malfunction has been solved.

Summary:

The 4013 faults are not caused by the iPhone baseband problem, which is due to the breakdown of the main CPU because of the threaded holes. It is very important to observe and judge the actual repair.

If you need more cell phone repair tutorials, please contact us on www.vipfixphone.com

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...
1 条评论
阅读全文