跳至主要内容

Guide: iPhone 7 Plus Error 56 Failure Repair

The iPhone 7P displays the iTunes icon, and when it connects to the computer for recovery, it reports error 56. When it reaches 80%, the error code is the same as the previous model, usually caused by camera power and NFC.


The resistance of each circuit power source of the camera is not abnormal. Checking the NFC section has a common fault in iPhone 7P. The NFC power supply can connect the short circuit at the upper left corner of the CPU.


Short A1 and A2 pins in the NFC power supply tube, then restore to short after the test connection. This iPhone 7P is still unable to pass, so we can only take NFC to test.


It is no problem to test the resistance of the socket by Fluke digital multimeter, reball the NFC module with iPhone BGA reballing stencil, install the NFC module and restore the phone after installation, but the mobile phone does not carry out the second self-examination and jump to iTunes, computer display recovery mode. There was no such situation before, so the first thing was to go out and exclude it. In order to prevent the external device from entering iTunes directly in the case of short circuit, when the computer exits the recovery mode, the iPhone volume flex cable and the tail plug flex cable interface are still not touched.

It's not expected that would happen elsewhere. The system is up-to-date, just choosing to keep the data to recover the machine, then discussing with the customer, deciding on a new reflection, without keeping the data, and consequently accessing the activation interface normally.

This 7P brush machine 56 error is due to NFC module virtual welding, keep the data on the phone does not enter the system, this is due to the original system there are damaged files.

If you want to get more details, check on www.vipfixphone.com

评论

此博客中的热门博文

Solution: iPhone X Won't Turn On

According to the customer's description, the iPhone X would not turn on after it drop accidentally. Then the cell phone reports error 56 when restore it. How did this happen? Let's test and repair step by step. Since iPhone X motherboard 2 layers are connected through the middle column, the solder points are very easy to get dropped. so we guess that the solder points from NFC chip to the CPU part have fell off. Disassemble the iPhone X by iPhone opening tools , remove the upper board off the main board, when separate the main board we see there is a row of points have fell off. Check the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Then the tin of the middle column is repaired by iPhone X BGA reballing ste...

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...

Solution: Why iPhone X Voltage Keeps Jumping

After getting the iPhone X motherboard to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU  power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...