跳至主要内容

Fixed: iPhone 6P Backlight Display Problem


A customer sent us an iPhone 6 Plus to fix it. The problem described was that the iPhone 6 Plus didn't show image or backlight fault. The motherboard had been repaired once. How to repair the problem? Let's check in this article!

After receiving iPhone 6 Plus, the appearance of iPhone 6 was not obviously damaged.

Use phone opening tools to disassemble the iPhone, take out the iPhone motherboard. Put iPhone motherboard under the Trinocular Stereo Microscope to observe, we found the iPhone display touch IC of the iPhone motherboard, iPhone light control IC U1501 and NUT column all have been removed. Moreover, the bottom of the NUT column on the iPhone motherboard has been hit by a long screw. 

Use QUICK 861DW hot air rework station and BGA remove graver to scrape it, there is no disconnection phenomenon.


Measuring the resistance value for the D3# layer of the iPhone display touch power supply IC U1501 by digital multimeter, there is no resistance, which is abnormal.

After check iPhone schematic diagram on the WUXINJI Dongle, we use QUICK 861DW hot air rework station to solder a jump wire from resistor R0302 to U1501D3#, and then install a good U1501.


After installation, iPhone 6P is measured again, and the data is normal now. Install the iPhone, and open it for testing, the iPhone shows normal, other functional tests are normal, the fault has been fixed!

More cell phone repair solutions, please read on www.vipfixphone.com

评论

发表评论

此博客中的热门博文

Solution: Why iPhone X Voltage Keeps Jumping

After getting the iPhone X motherboard to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU  power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
发表评论
阅读全文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文