跳至主要内容

iPhone 6S Rear Camera Failure Repair

We are going to repair an iPhone 6s today, the main failure is that the iPhone 6S rear camera can not be used. After getting the device, we first install and test to confirm the failure. How to fix it step by step? Let's check in the article:
 

1. First of all, use iPhone 6S opening tools to disassemble the phone and remove the motherboard to observe carefully.

2. After we remove the motherboard, we found that the board is good, and the real camera socket is also pretty.

3. Next we have to check the motherboard and test the resistance of the socket with a Fluke digital multimeter. We found that the 13 pin of the socket have no resistance.

4. The 13 pin is communicant to the FL3110 beside WiFi chip, the inductance is off, so we need to short connect by jumper wire.


5. install the iPhone 6s to test again, iPhone 6S rear camera can be used normally, the fault is fixed successfully.

More professional phone failure solutions check on www.vipfixphone.com

评论

  1. Golden Nugget Casino New Orleans - MapYRO
    Golden Nugget Casino New Orleans in New Orleans 포천 출장마사지 offers the finest gaming 삼척 출장샵 experience in New Orleans, the 청주 출장샵 only AAA Four Diamond resort in 강릉 출장안마 the world to 울산광역 출장안마 have

    回复删除

发表评论

此博客中的热门博文

Solution: iPhone X Won't Turn On

According to the customer's description, the iPhone X would not turn on after it drop accidentally. Then the cell phone reports error 56 when restore it. How did this happen? Let's test and repair step by step. Since iPhone X motherboard 2 layers are connected through the middle column, the solder points are very easy to get dropped. so we guess that the solder points from NFC chip to the CPU part have fell off. Disassemble the iPhone X by iPhone opening tools , remove the upper board off the main board, when separate the main board we see there is a row of points have fell off. Check the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Then the tin of the middle column is repaired by iPhone X BGA reballing ste...

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...

Solution: Why iPhone X Voltage Keeps Jumping

After getting the iPhone X motherboard to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU  power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...