跳至主要内容

Guide: iPhone 7 Plus Charging Part Repair


Have you ever met the situation on your iPhone 7 Plus? If it has a charging problem, such as iPhone 7P will not charge, can not connect to PC, iPhone charging icon percentage decrease, stuck on white apple, etc. all these charging problems, you need to check iPhone 7 plus charging part.


Check iPhone schematic diagram on WUXINJI Dongle, 5V charge voltage PP5V0_USB  sent by the tail-plug interface，one circuit is sent to iPhone charge IC, one circuit is sent to iPhone USB control IC. The repair method is as follows.

Disassemble the iPhone 7 Plus with phone disassemble kits, remove the iPhone motherboard.

Measure the 5.0V voltage (PP5V0_USB) next to the iPhone charging IC with
Fluke 15B+ Digital Multimeter to check whether it exists. If not, then you need to replace the new iPhone tail plug flex cable. If yes, continue to check.

Measure the 5.0V voltage (PP5V0_USB) next to the iPhone USB control IC with multimeter to check whether it exists. If not, then you need to use QUICK 861DW hot air rework station to solder the jump wire from 5.0V voltage (PP5V0_USB) next to the iPhone charging IC to 5.0V voltage (PP5V0_USB) next to the iPhone USB control IC. If 5V is exist， then you need to replace the iPhone USB control IC and iPhone charge IC.

More cell phone repair tutorial, please contact us on www.vipfixphone.com

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...
1 条评论
阅读全文