跳至主要内容

How To Fix iPhone 7P Front Camera Fault


We are going to fix an iPhone 7 Plus today, the problem is that the iPhone 7 Plus front camera not working. How to fast fix the fault? Let's read the detailed steps in the article!

After we receive iPhone 7 Plus, we will test it first. Open iPhone 7 Plus, enter iOS, open the iPhone camera icon, iPhone rear camera normal, switch to iPhone front camera, iPhone 7 plus front camera do not work, display black.

Untie iPhone 7 plus the phone opening tool, and carefully remove the iPhone motherboard.

Put the iPhone main board on the WL aluminum alloy pad.
Measure the ground resistance for iPhone front camera socket J4503 by Fluke 15B+ DigitalMultimeter, the data tested is normal. And then measure the iPhone front camera power supply, the data tested also is normal. However, when we measure the I2C bus, we find the voltage for I2C_NH_SCL_CONN only have 0.62V, which is abnormal.

After check the iPhone 7 Plus schematic diagram in the WUXINJI Dongle, we need to replace the resistor R4812.


Take an new resistor R4813, remove the old resistor R4812 from iPhone motherboard, and then install the new resistor R4813 by QUICK 861DW hot air rework station.

After installation, measure it again, the data is normal now.

Assemble the iPhone, and get into IOS to test the iPhone camera, the iPhone front camera works properly.

If you want to read more cell phone repair skills, please contact on www.vipfixphone.com

评论

发表评论

此博客中的热门博文

Solution: iPhone X Won't Turn On

According to the customer's description, the iPhone X would not turn on after it drop accidentally. Then the cell phone reports error 56 when restore it. How did this happen? Let's test and repair step by step. Since iPhone X motherboard 2 layers are connected through the middle column, the solder points are very easy to get dropped. so we guess that the solder points from NFC chip to the CPU part have fell off. Disassemble the iPhone X by iPhone opening tools , remove the upper board off the main board, when separate the main board we see there is a row of points have fell off. Check the location map on WUXINJI dongle , it is surrounded by a ground wire, in fact, there are 6 useful points dropped. The ground wire does not need to be filled, the 6 useful points are added by professional phone welding tools. These are the signal wires of the NFC chip, so the iPhone X would report error 56. Then the tin of the middle column is repaired by iPhone X BGA reballing ste...
发表评论
阅读全文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Solution: Why iPhone X Voltage Keeps Jumping

After getting the iPhone X motherboard to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU  power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
发表评论
阅读全文