跳至主要内容

How To Fix iPhone 7P Front Camera Fault


We are going to fix an iPhone 7 Plus today, the problem is that the iPhone 7 Plus front camera not working. How to fast fix the fault? Let's read the detailed steps in the article!

After we receive iPhone 7 Plus, we will test it first. Open iPhone 7 Plus, enter iOS, open the iPhone camera icon, iPhone rear camera normal, switch to iPhone front camera, iPhone 7 plus front camera do not work, display black.

Untie iPhone 7 plus the phone opening tool, and carefully remove the iPhone motherboard.

Put the iPhone main board on the WL aluminum alloy pad.
Measure the ground resistance for iPhone front camera socket J4503 by Fluke 15B+ DigitalMultimeter, the data tested is normal. And then measure the iPhone front camera power supply, the data tested also is normal. However, when we measure the I2C bus, we find the voltage for I2C_NH_SCL_CONN only have 0.62V, which is abnormal.

After check the iPhone 7 Plus schematic diagram in the WUXINJI Dongle, we need to replace the resistor R4812.


Take an new resistor R4813, remove the old resistor R4812 from iPhone motherboard, and then install the new resistor R4813 by QUICK 861DW hot air rework station.

After installation, measure it again, the data is normal now.

Assemble the iPhone, and get into IOS to test the iPhone camera, the iPhone front camera works properly.

If you want to read more cell phone repair skills, please contact on www.vipfixphone.com

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Solution: Why iPhone X Voltage Keeps Jumping

After getting the iPhone X motherboard to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU  power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文