跳至主要内容

Guide: iPhone 6S No Display Repair


Received an iPhone 6S, it was not displayed after turning on. The iPhone 6S accidentally fell into the water, but the owner quickly took it out and it didn't seem to have been much damaged, but the iPhone 6S could still be turned on. How to repair the problem? Let's check in the article!


After receiving iPhone 6S, we need to test it first. Press the power button on the iPhone and the screen stays black. We try to call it using another iPhone. It works. The iPhone 6S responds, but the iPhone LCD screen is still not displayed.

Open the iPhone and connect it to the DC power supply to test the iPhone boot current, the current data tested is normal, which means the iPhone can be turned on smoothly. Now, we confirm the failure is that the iPhone doesn’t display.

Take out the iPhone motherboard, observe it under the Stereo Zoom Microscope, there are small trace of water on the iPhone motherboard. Carefully clean it up, and then continue to observe.

Observing the iPhone display socket and those inductance resistances around it, we found the FL4220 is virtual welding. We can open the WUXINJI Dongle to find the FL4220 place in the iPhone schematic diagram.


Now, use tweezers to remove the FL4220, and the use QUICK 861DW hot air rework station to short connect it.  Check if the surrounding inductor also has a virtual weld, if yes, we can short connect it by jump wire. After observation, there is no other inductors has a virtual weld.


Install iPhone and test it. Now the iPhone LCD screen is displayed normally. The repair is finished.

More professional cell phone repair details, check on www.vipfixphone.com

评论

发表评论

此博客中的热门博文

iPhone 6 Display Failure after Replacing LCD

The iPhone 6 display is black after replacing LCD. After checking, the diode data of display socket is normal and all power supply for iPhone display IC  output is normal. Testing by  DC power supply , we find the iPhone current is abnormal. When press the iPhone power button, the boot current is obviously large. The current reached 100mA when press the power button. After remove the display tube, the current still the same, which means there is a short circuit. Measure the voltage output of each circuit of power supply with Fluke 15B+ Digital Multimeter , then surprised to find that there are really short circuit places. LD010 is short circuit; we suspect that the filter capacitance on the circuit has been penetrated. After remove the iPhone power control IC , we found it is ground short circuit. Open the WUXINJI Dongle  to check the iPhone schematic circuit, we found that this circuit is the display card image transmission MIPI data bus power supply. CPU brea...
发表评论
阅读全文

Iphone 6S Enters DFU Mode Cannot Start Fault Repair

The customer said that he did not know what the reason was. The mobile phone has been restarted indefinitely and can enter the DFU mode. However, when the flashing machine fails to enter the recovery mode from the DFU mode, and then the mobile phone is connected to the computer for 5-10 minutes, it automatically enters the recovery mode. After we received the 6S that could not be started, we disassembled the power with iphone engraving tool and turned on the power to 100mA. First of all, check if you can connect and read the DFU mode after connecting to the computer. Wireless DFU can not exit, we can only brush the machine to view the error. Refresh Aisi and iTunes respectively. If you stuck on the progress bar for a long time, it is very likely that the error is -1. If the progress bar does not enter, you can roughly determine the probability of a CPU failure. Now we need to see if there is a problem with the hard drive. First, use DC power supply for iphone repair, the hard disk o...
发表评论
阅读全文

Tutorial: iPhone 6S Plus Backlight Repair

Since the size of iPhone6s plus screen display  is large, it's necessary to use two sets of background lights to supply power, one is provided by U4020, the other is provided by U4050. 2  sets of circuit 1) PP_LCM_BL_ANODE,     PP_LCM_CAT1, PP_LCM_BL_CAT2 2) PP_LCM_BL34_ANODE,  PP_LCM_BL_CAT3, PP_LCM_BL_CAT4 For PP_LCM_BL_ANODE and PP_LCM_BL34_ANODE, if one of the circuit has no voltage value, it will cause the iPhone 6s Plus screen to be half bright and half dark. For PP_LCM_CAT1, PP_LCM_BL_CAT2, PP_LCM_BL_CAT3 and PP_LCM_BL_CAT4, if one of  these four circuits gets abnormal signal, it will cause the 1/4 screen to be dark. Solution: Use jumper wire  to short connect PP_LCM_CAT1 and PP_LCM_BL_CAT2 or you can also connect PP_LCM_CAT3 and PP_LCM_BL_CAT4. The control signals of these two sets of backlights, one group of inductors FL4211 FL4212 FL4213 are sent to the display interface. The other group is sent to the display interface...
1 条评论
阅读全文